06.57 www.demos‑trade.com 1 000 1 000 L H D 20 220240 V 20 220240 V 20 220240 V 3 405179 88 × 39 × 28 405180 85 × 50 × 32 405181 116 × 52 × 33 405182 116 × 56 × 34 353250 1] 172 × 73 × 43 405183 160 × 30 × 16 405184 160 × 58 × 18 405185 184 × 64 × 22 405186 170 × 57 × 32 405187 180 × 66 × 32 405178 58 × 26 × 35 LIGHTING AND ELECTRIFICATION OF FURNITURE StrongLumio power supplies 12 V • round connector with grey socket (12 V) at the output • in order to achieve optimal function, it is recommended to have the power supply as close to the light source as possible (longer cables cause voltage losses and a subsequent drop in luminous intensity, they may also have disturbing influence on nearby electrical appliances) • power supply should have a minimum distance of 0.5 m from other electrical appliances • power supplies must be located in such a way that sufficient ventilation – heat dissipation, if located in a closed room, sufficient ventilation (ventilation holes) must be provided • input power of the power supply must be higher than the input power of the lights, recommended reserve: 20%, for continuous lighting the reserve should be increased to 30% • cable length 2 × 1 m 1] the power supply has a three core detachable power supply cable and two round connectors on the output Principles for choosing and installation Flat 12 V power supplies Adapter for 12 V socket 12 V power supplies • for power supply of LED strips and lights with 12 V voltage, direct current • power supply: 220–240 V, 50 Hz • for power supply of LED strips and lights with 12 V voltage, direct current, grey edges (12 V) • power supply: 220–240 V, 50 Hz • plug-in design with grey connector socket (12 V) • for power supply of LED strips and lights, supply voltage: 12 V, direct current • circular connector at the output • in order to achieve optimal function, it is recommended to have the power supply as close to the light source as possible (longer cables cause voltage losses and a subsequent drop in luminous intensity, they may also have disturbing influence on nearby electrical appliances) • power supply should have a minimum distance of 0.5 m from other electrical appliances • power supplies must be located in such a way that sufficient ventilation – heat dissipation, if located in a closed room, sufficient ventilation (ventilation holes) must be provided • cable length 2 × 1 m Warning It is not possible to combine 12 V LED strips with a 24 V transformer and vice versa. The power supply must always have sufficient reserve for the respective LED strip set. During normal use, the reserve should be 20%, if used for more than 5 hours, we recommend increasing the reserve to 30% or more. Offered power supply have protection to prevent damage, the transformer switches off at overloading and after reducing the load and cooling, the power supply is functional again. However, overloading has a negative impact on the overall service life. The power supply should be installed in such a way that it can be accessed at any time for replacement and is well ventilated. Installation in small, unventilated space reduces its service life. Please note that the supply voltage must comply with ČSN EN 60038, damage due to over-voltage in the electrical network is not a reason for placing a complaint. Claims are resolved by replacing the faulty power supply. Additional costs associated with replacing the connection are not recognised. YEARS WARRANTY Power supply power (W) = x+ 20% (30%) x = LED strip length (m) × LED strip input power (W/m) Example: using a strip of 14.4 W/m and an installed strip length of 2.5 m, the strip power is 36 W + 20% reserve (7.2 W) = 43.2 W. You will therefore need a power supply with a minimum power of 44 W. code power L × D × H (mm) 18 W / 1.5 A 30 W / 2.5 A 48 W / 4.0 A 80 W / 6.6 A 120 W / 10 A code power L × D × H (mm) 15 W / 1.25 A 30 W / 2.5 A 60 W / 5 A 75 W / 6.25 A 100 W / 8.33 A code power L × D × H (mm) 6 W / 0.5 A
RkJQdWJsaXNoZXIy MzEyMDA=